EasyPSV® Holographic

Fast Shipping Policy Facts:

  • Done Added as extra charge
  • Done UPS is our official carrier
  • Done Next day ground service option only (for now)

Description

Boasting the same pearlescent finishes as the HTV Holographic Pearl line,  EasyPSV Holographic Pearl offers a stunning, reflective look for hard goods. All 6 colors are
available in EasyPSV, including Rainbow Pearl, Mystic Pearl, Moonlight Pearl, Firelit Pearl, Tropical Pearl, and Rainforest Pearl.

Warnings
  • Not for use on walls or for temporary applications.
  • Not recommended for use near flame/heat source.
  • Not microwave or dishwasher safe.

EasyPSV Holographic Pearl contains a permanent adhesive and is not recommended for temporary applications. Has an opalescent finish that changes depending on the garment.

Holographic EasyPSV Applies To:

  • Wood
  • Glass
  • Plastic
  • Ceramic
  • Metal

Cutter Settings

Cricut Explore Air: Blade: AutoBlade, Standard  Setting: Vinyl
Cricut Maker: Blade: AutoBlade, Fine-Point  Setting: Vinyl
Brother Scan N Cut DX: Blade: Standard, 3  Cut Speed: 1  Cut Pressure: 2
Silhouette Cameo 4: Blade: AutoBlade, 2  Material: Vinyl, Glossy  Force: 7  Speed: 8
Roland GX/GS-24: Blade: 45°  Gram Force: 80-110  Offset: .250  Speed: 30-50 cm/s
Graphtec: Blade: 45°  Gram Force: 9  Tool: CBO9U+0  Speed: 30 cm/s
US Cutter Titan 2 & 3: Blade: 45°/60°  Gram Force: 50-55  Speed: 300 mm/s  **Blade Advancing Varies
Mimaki CG-60SR III: Blade: 45° Gram Force: 50  Offset: 30  Speed: 20-30 cm/s
Brother Scan N Cut: Blade: Standard, 3  Cut Speed: 1  Cut Pressure: 2

The specifications listed are suggested starting points that may need to be adjusted according to blade, cutting strip and cutting mat wear. Always perform a test cut prior to cutting designs.

*Craft cutters were evaluated using cutter-specific standard grip cutting mats.

Specifications

Outdoor Durability Up to 5 years depending on climate and UV exposure.
Thickness 3.0 mil (76.2 micron)
Adhesive Permanent, Water Based
Liner 78# Kraft
Minimum, Application Temperature +40° F
Shelf Life 1 year when stored at 70° F and 50% relative humidity

Application Instructions

Print and Cut Instructions:

  1. Print and cut your design (do not reverse/mirror)
  2. Weed excess vinyl
  3. Remove application tape’s paper liner and place on top of EasyPSV
  4. Burnish with a Squeegee
  5. Place on desired object and burnish with a squeegee
  6. Peel away the application tape

Application Instructions:

  1. Preheat garment for 2-3 seconds
  2. Apply design at 311°F / 155°C
  3. Use medium/firm pressure for 5 seconds
  4. Peel carrier Hot
  5. Re-cover design and press for 20 seconds

Surface Prep

  • For best adhesion, remove any dirt, dust, grease, etc to prepare the surface you want to decorate with EasyPSV.
  • The following cleaning method is not recommended for porous surfaces such as unfinished/untreated wood.
  • It is recommended that all other surfaces be spot tested with care before cleaning the entire application area.
  • Non-porous surfaces can be cleaned with a mix of approximately 2 parts water and 1 part isopropyl alcohol (70% or higher for best results) or non-amonia based window cleaner.
  • Use a microfiber or lint free towel to clean the application area with the mixture.
  • Paper towel is not recommended since it will leave behind small bits of paper that can become trapped under the EasyPSV during application.
  • Ensure the area is completely dry before applying.

*The cleaning method outlined above is subject to modification and not always suitable for every substrate.

The purchaser should independently determine with their own testing to use this method or not on a case by case basis.

Removal

  • If the EasyPSV peels up, but leaves an adhesive residue use an adhesive remover to clean the area.
  • If the EasyPSV is stubbornly sticking, the heat from a hair dryer or garment steamer can help loosen the adhesive.
  • However, heating is not recommended for glass due to possible shattering.
  • To remove Permanent EasyPSV from glass, saturate the decal with soap and water.
  • Cover with plastic wrap and let sit for a few hours before attempting to remove.
  • An adhesive remover may still be required to clean all adhesive from the surface after removing the EasyPSV.

*The removal instructions outlined above are subject to modification and not always suitable for every substrate.

The purchaser should independently determine with their own testing to use this method or not on a case by case basis.

Videos